Sharper Image EC-WS115 Bedienerhandbuch Seite 1

Part No: AWS-110 / AWS-220103 Bauer Drive, Oakland NJ 07436 • 800-648-7229 • Fax: 800-286-0114www.alpha-tools.comAlpha® Wet Stone CutterInstruction Ma

10 GROUND FAULT CIRCUIT INTERRUPTER: DANGER! Do not bypass the GFCI if this condition occurs, a real shock hazard may exist. WARNING!If the GFCI fai

112.CheckitemsbelowwhentheGFCIgoesOFFfrequently. • Forceappliedonthestonecutter. • Waterenteredinsidethestonecutter. • Vol

12 WARNING!1. Before turning the switch ON, make sure the rotating parts are not touching anything. If the switch is turned ON while they are in

13 INSTALLATION OF WATER ATTACHMENT1. Remove the wing screw and washer for adjusting the cutting depth. (See Figure-6)2. Raise cutting depth so th

14 WATER FLOW DANGER! Always check that the GFCI unit is working correctly (reset, test, and reset) before using this tool in a wet condition. Do

15 CAUTION!Allow the saw blade to do the work, applying excessive forward pressure to the tool will slow down the RPM’s and burn up the motor, which

16Wing screw for adjusting cutting depth OPTION 3: USING THE CARRIAGE ASSEMBLY AND GUIDE RAILInstall the guide rail 2-3/4 inches / 70mm from the inten

17BLADE INSPECTION, INSTALLATION, AND REMOVAL DANGER!Be sure to unplug the power cord from the outlet before attaching or removing the saw blade from

18AWS-110 MAINTENANCE DAILY1. Before daily start-up inspect tool, power cord, GFCI, and Saw Blade, looking for chips and cracks.2. If damage has occ

19REPLACING AND CHECKING THE CARBON BRUSHESIn order to keep your tool running correctly, you need to check your carbon brushes after every one hundred

2TABLE OF CONTENTSIntroduction ... 3 Abo

20Proper Alignment4. Install new carbon brush with the proper alignment of the brush holder followed by the cap as shown in Figure 20.Figure-20Old Ca

21Note: If you notice any resistance while tightening the carbon brush cap, it is an indication that the top plate on the carbon brush assembly is st

227. Check to see if the two parts move freely by pushing the top plate of the carbon brush into the recess on the bottom of the carbon brush cap and

23RECOMMENDED ACCESSORIESThis is the blade for cutting reinforced rod channels into granite or marble countertops. No longer is there a need to employ

24ALPHA® AWS-110 WET STONE CUTTER SCHEMATICAWS-110 / AWS-220

25 ALPHA® AWS-110 WET STONE CUTTER PARTS LISTDRAWING NO.. PART NO. DESCRIPTIONQUANTITY1133080 Screw M5x40 32130031Self-tapping Screw 3.9×19 731332

26ALPHA® AWS-110 WET STONE CUTTER PARTS LISTDRAWING NO. PART NO. DESCRIPTION PIECES37133082 Flange II (for AWS-110) 138133464 Screw M6×20-Left 1391330

27Optional: Alpha® Guide Rail and ClampOPTIONAL: CARRIAGE ASSEMBLY SCHEMATICPART NO. AWS-UCAM

28CARRIAGE ASSEMBLY PARTS LISTDRAWING NO. PART NO. DESCRIPTION QUANTITY1 133285 Screw cap M8 42 133252 Washer 9×16×1.6 43 133383 Guide Rail Carriage 1

29EC DECLARATION OF CONFORMITY Name of Manufacturer: Alpha Professional Tools® Address of Manufacturer: 103 Bauer Drive Oakland, NJ 07436 U

3INTRODUCTIONThank you for purchasing the Alpha® AWS-110 Wet Stone Cutter Please read this instruc-tion manual thoroughly to ensure safe and correct

30SERVICES AND WARRANTY INFORMATION LOANER PROGRAM:Loaner tools can be issued to temporarily replace a tool that is being returned to Alpha® for repa

31PRODUCT REGISTRATION CARDModel No. Serial No.Company Name: ______________________________________________Name: ___________________

Copyright © 2012 Alpha Professional Tools. All rights reserved. 103 Bauer Drive, Oakland, NJ 07436 • Fax: 800-286-0114www.alpha-tools.com7/05/12

4Note: In some situations, failing to observe WARNING notes could result in death or serious personal injury. Be sure to read and observe the sa

510. Do not abuse the electrical cord Never carry the tool by the electrical cord or pull it to disconnect from receptacle. Keep the electrical cor

6AWS-110 OVERVIEW SPECIFICATIONSRating ...110/220 VoltsA

7 ACCESSORIESCOMPONENTS: 1. Ground Fault Circuit Interrupter (Part No. 133289/133292)2. Water Valve (Part No. 133362)3. Water Attachment Assembly (

8ADDITIONAL PRECAUTIONS FOR USING THE WET STONE CUTTERIn addition to the general safety notes described on the preceding pages, please read and obser

9• Alwaysuseandstorethesawbladesaccordingtothemanufacturer’sinstructions.Theangeboltmustbetightenedbeforestartingtoworkwithth